FEATURES
Full lightning and surge protection.
Uninterrupted operation even under the harshest environmental conditions.
Ultra linear transistors provide high output capability for optimum signal handling.
High gain and ultra low noise figure from latest generation transistors give optimum sensitivity.
Simple installation -hardware included.
Rugged die-cast aluminum housing -fully shielded.
Surface-mounted components for automated production and consistent high performance.
Cool running, redesigned 117 VAC power supply, Model 0747 is included with each model. Output voltage is +15VDC. UL and cUL listed, Power supply also available as a separate model.
Model 7778 offers Spartan 3TM specifications in the die-cast TitanTM housing and is compatible with Model 7763 Tandem Amplifier.
This Preamplifier, CM7778, is great with lightning protection.
You can use the
1296F as a variable attenuator to control the Db Gain
Learn How to install a pre-amp by clicking here
Compare with other pre-amps by clicking here
16dB of gain on VHF and UHF Band
SPECIFICATIONS
A Pre-Amplifier (pre-amp) is a mast or antenna mounted amplifier used primarily to eliminate "snow" on the TV screen. Snow is actually electrical noise that is generated by the TV receiver and other electrical devices. The objective of any antenna installation is to deliver enough signal to the TV set to override the noise (snow). A "weak" signal is one that is not strong enough to override the level of the noise in the set. Another obstacle is the signal loss incurred while traveling through the transmission line connecting the antenna to the TV set. An antenna that has acceptable gain at the antenna tapoffs but encounters excessive loss due to long cable runs will also deliver a "snowy" picture to the TV set due to not enough signal makes it to the set to override the noise level. A pre-amp would be used to compensate for the losses in the transmission line as well as the noise level of the set.
TITAN 2TM
MATV Mast Mounted Preamplifiers
The Titan range of mast mounted amplifiers has been completely reengineered and updated. These amplifiers represent the ultimate in preamplifier performance. They are designed for use as an ultra low noise, ultra high gain preamplifier for deepest fringe applications and MATV headend applications.
Their very high signal handling also makes them suitable for use as a mast mounted, ultra low noise distribution amplifier for use in small MATV systems. All models feature 75 ohm, input and output connections in line with modern headend engineering practice.
SPECIFICATIONS:
- Number of Inputs: 1 (VHF & UHF)
- Input and Output Impedance: 75 Ohms
- Input and Output Connectors: F Type Connectors
- VHF Gain: 16 dB
- Switchable FM Trap
- UHF Gain: 16 dB
The power supply that comes with this amp goes inside the building, so you do not have to run a separate cable for power. The unit inside the building injects voltage up the coax cable, so there is no need to put a power supply outside. Be sure not to place any devices in-line between the pre-amp and power supply, or the voltage will be blocked and the unit will not function correctly.
REVIEWS
Product Review Summary
Product Reviews for Channel Master CM7778 Titan 2 VHF/UHF TV Antenna Preamplifier with Power Supply (CM-7778)
Own one? Write a Review!
Average Rating (1 Reviews): 
|
Five Stars:
|
|
0 (0%)
|
|
Four Stars:
|
|
0 (0%)
|
|
Three Stars:
|
|
1 (100%)
|
|
Two Stars:
|
|
0 (0%)
|
|
One Star:
|
|
0 (0%)
|
Latest Positive Rating:
Great distance quality but short life
All Customer Reviews
Great distance quality but short life
Joe - Dothan, AL - 2/27/2011
pulled in stations up to 100 miles with great picture.My only complaint is that I had two to go bad in two years.
NEED TV ANTENNA HELP?
