Availability: Usually Ships Same Day Condition:New
Your Price: $6799 List Price: $99.99
Amplify UHF and VHF signals received by your outdoor TV antenna with the Titan 2 preamplifier. This high-gain, low- noise preamplifier solves common signal issues for strong, clear reception. This preamp and power supply connect to your antenna using RG6 coax cable. Makes up for signal loss due to long cable lengths and splitters. The Titan series mast-mounted amplifiers by Channel Master represent the ultimate in pre-amplifier performance.
30dB gain makes this one of the strongest preamplifiers you can buy
Power supply safely remains indoors, away from the elements, and sends voltage up the coax cable to power the outdoor amp near the antenna
Improved circuitry for lightning and surge protection
Optimum filtering for rejection of out-of-band signals
Switchable FM trap blocks potential radio interference
Power supply and pre-amp are connected to the antenna using RG6 coax cable. An RG6 cable is run from antenna to pre-amp, from pre-amp to power supply, then from power supply to television. Power supply does not have to be outdoors
Cool running, redesigned 117 VAC power supply, Model 0747 is included with each model. Output voltage is +15VDC. UL and cUL listed, Power supply also available as a separate model
Power supply goes in the building and sends voltage up the antenna cable (see diagram in Specifications tab)
Surface-mounted components for automated production and consistent high performance
Preamplifier and its power supply can withstand up to 140° F temperatures
You can use the 1296F as a variable attenuator to control the Db Gain
Improved circuitry for full lightning and surge protection
Optimum filtering for rejection of out-of-band signals
Makes up for signal loss from long cables and splitters
A Pre-Amplifier (pre-amp) is a mast
or antenna mounted amplifier used primarily to eliminate "snow" on
the TV screen. Snow is actually electrical noise that is generated by the TV
receiver and other electrical devices. The objective of any antenna
installation is to deliver enough signal to the TV set to override the noise
(snow). A "weak" signal is one that is not strong enough to override
the level of the noise in the set. Another obstacle is the signal loss incurred
while travelling through the transmission line connecting the antenna to the TV
set. An antenna that has acceptable gain at the antenna tapoffs but encounters
excessive loss due to long cable runs will also deliver a "snowy"
picture to the TV set due to not enough signal makes it to the set to override
the noise level. A pre-amp would be used to compensate for the losses in the
transmission line as well as the noise level of the
Mast Mounted Preamplifiers
The Titan range of mast
mounted amplifiers has been completely reengineered and updated. These
amplifiers represent the ultimate in preamplifier performance. They are
designed for use as an ultra low noise, ultra high gain preamplifier for
deepest fringe applications and MATV headend applications.
very high signal handling also makes them suitable for use as a mast mounted,
ultra low noise distribution amplifier for use in small MATV systems. All
models feature 75 ohm, input and output connections in line with modern headend
SPECIFICATIONS: • Number of
Inputs: 1 (VHF UHF • Input and Output Impedance:
75 Ohms • Input and Output Connectors: F Type Connectors •
The power supply that comes with this amp goes
inside the building, so you do not have to run a separate cable for
power. The unit inside the building injects voltage up the coax
cable, so there is no need to put a power supply outside. Be sure not
to place any devices in-line between the pre-amp and power supply, or the
voltage will be blocked and the unit will not function
Here are available downloads related to this product:
Product Reviews for Channel Master Titan 2 High-Gain UHF VHF TV Antenna Preamplifier (CM-7777)
Product reviews help other customers decide which product to purchase, where the best deals are, and your get a sense of
what to expect with the product. Write a Review!
Average Review (23 reviews):
Recent Review: Sooner89 - Hartshorne, OK - 8/5/2015 Still the best, bar none.
Still the best, bar none. Sooner89 - Hartshorne, OK - 8/5/2015 11:31:49 AM The most powerful on the market.
And then it appeared....... Mr.DIY'er - Genoa City, WI - 4/19/2015 12:49:21 AM A high quaility picture, not just one or two, it came with friends and all clear as crystal they were. After reading the trials and tribulations, from others, of finding the best possible ota antenna setup I settled on the CM3020 antenna mounting to chimney originally but later deciding against this type mount, after it broke during installation, and ultimately mounting it in the attic where I knew I'd lose some range however I had plenty enough antenna to work with so worth a shot. After antenna install I ended up with a considerable cable run of 100 + feet to tv. After a quick scan for channels I was only able to receive a few channels at moderate clarity. I feared it was due mostly to structural interference or maybe the lengthy run or both. After reading many reviews on the CM7777 I purchased it to see if it cured the issue, BINGO! Took all of 45minutes to hook up and I was receiving over 30 channels in very high quality. I am located 50+ miles away from the towers so was super Happy with these results! I would recommend this setup to anyone living in a fringe area and needing to pickup weaker signals and/or have long cable runs. I have cutoff my cable provider and now enjoy Free TV! Thank you Solid Signal for the excellent customer service and fast shipping you guys rock! A quick note on the CM3020, it's very large in size, not the easiest thing to maneuver in the attic but gets out there so if you can fit it and don't have the option of outdoor mounting then this will fit the bill. I suspended this antenna from the rafters with string pointing towards my closest towers and I get all the channels I watch with many extra I didn't expect. Nice work Channel Master! Hope this review helps you make the best choice and frees you from the clutches of a The Cable Guy.
Welcome to A CM7777AMP kenney - INDIAN ORCHARD, MA - 9/30/2014 12:59:02 PM I HAVE A HDB91XG WITH THE CM7777AMP WHAT AN AWESOME AMP AND WHAT A GOOD MATCH FOR THE HDB91X I LIVE IN INDIAN ORCHARD MASS I GET STATION 80MILES OUT IN NY CITY AND CT WELL DONE AND THANKS SOLID SIGNAL KEN
Well done channel master kenney - INDIAN ORCHARD, MA - 9/13/2014 10:56:57 AM Well fit for a XG91 WITH the CM7777AMP I GET STATION 80MILES OUT day or night time well done solidsignal THANKS KEN
11 Channels perfectly clear. BYE BYE satellite !! Dish Network !!! TJ - Silver Cliff, WI - 3/17/2014 2:27:15 PM Excellent pre amp and anntena !!
made a noticeable difference Zim - Marysville, CA - 12/30/2013 1:34:50 PM had a cheap RCA preamp on our antennas but when I had to relocate the antennas to the other side of the house to avoid a neighbors tree the signal got weak enough that it was borderline quite often. There is a good 75 feet of cable now between the antenna and the TV. Swapped out the amps and on the HD Homerun signal strength went from low 50s to solid 70. Before when the antenna would move at all the signal would fail. Now turning it a bit from side to side doesn';t affect the signal at the TV.
Better performance than older tech. DrOrb - Port Charlotte, FL - 7/5/2013 8:58:27 AM My CM0747 gave up the ghost after 7 1/2 years. The replacement, CM7777 is better performing, bringing in twice the number of distant programming.
One small detail, the signal does *not* come from the power supply; there is a signal/power splitter installed between the amp and PS. This is elegant since the AC outlet may be distant from the signal run.
HDTV reception excellent Kenny - Old Town, ownFla. - 3/28/2013 The product results was better than expected (for my area).I live 45 miles from Gainsvile Fla.130 from Tallahassee90 from Jaxsonville140 from Tampa and 60 from Ocalla. I have a very used antenna on a 40 ft tilt tower.I used as few couplings as possible on a 110 ft cable.Antenna rotor lets me swing to any of the locations and receive a very good HDTV signal
Enables UHF antenna for VHF-hi Waltro - Chicago suburbs, Chicago suburbs - 3/28/2013 My VHF locals are 29-miles away so it does not overload for me (as some say theyve experienced with a nearby VHF local or FM tower).Use it with a UHF bowtie (Antennas Direct DB4) antenna and it pulls in the VHF-hi stations reliably as well as the primary UHF stations.Without this preamp the VHF stations were dicey at best for me and pixilated during tree movement during storms.I prefe
good product Pete - Topsham, ME - 3/28/2013 I live in a marginal receiving area and the mast should be higher. I credit the preamp and good antenna for good reception. Everything seems sturdy and the outdoor unit appears durable and weatherproof.
Very Good Pre-Amp JohnnyRace - White Plains, ite Plains N - 3/28/2013 I am all DTV off air. Very good antenna preamp. Works exactly as described the picture does come in clearer as well as more channels are now viewable. With Digital TV some stations I now get video only since sound is broadcast separately I know the amp provides gain for the audio too but my tuner does not pick up all the new stations I now get with the amp installed with sound. So total I get
Very satisfied jj - damascus oregon, damascus oregon - 3/28/2013 Very easy to install.
CM7777 Works Perfectly JD Tractor - Milford, CT - 10/3/2011 Our home in CT is 62 miles from the transmitter in NYC and channels 2 CBS and 4 NBC were impossible to get.The 7777 is now mounted on our antenna approx. 25 off the ground and pushes through 50 of cable to a 3-way splitter.The TVs are then approx. 15 20 and 40 away and we enjoy a full range of channels on all of them including 2 & 4. Completely worthwhile investment.
Excellent product OTA Ant User - Worcester, ster MA - 5/5/2011 The TV/Ant terminals are labeled on the underside of the power supply. Once mounted the label cannot be seen. It would be better to label at the terminals. I marked them myself with a Sharpie pen.
Not as good as Winegard AP-8700 TVtechnician - Columbus, OH - 11/13/2015 2:17:03 PM After reading all the rave reviews here and all over the web I decided to give it a try
My Winegard AP-8700 has been working fine but I'm always looking for an extra db or two improvement if possible
I found that signal levels on the TV were no stronger with the CM-7777 than with the AP-8700
In fact the Winegard seems to have slightly better sensitivity since it was able to pull in one extreme fringe tv station that the CM-7777 couldn't
I switched them out several times each time checking all the signal levels and picture quality just to be positive that test conditions were identical
The old Winegard out performed the Channel Master every time
I like the fact that the CM-7777 is mounted in a metal housing and since the AP-8700 is no longer available I will keep the CM-7777 as a back up should the Winegard ever quit
Thought it was DOA.... but no paxplant - Duluth, GA - 2/23/2015 2:22:37 PM I live in a near fringe area and when I first connected this to the antenna I have in the attic I lost all signal... thought it was dead. Saw a review that said it could be shutting down because of to much signal, sure enough. I turned my antenna 180 (pointing away from the main broadcast towers). Now I'm pixel/freeze free on all the stations I wanted, but I did have to add in a dipole antenna to pickup one station that is off to the side. Only 4 stars because they should have something in the documents to let you know a strong raw signal can cause it to shutdown.
I would buy CM7777 Titan2 again. Jah T - Ohio, Ohio - 3/28/2013 Help me get Tv station that we needed
Works well get it done - Lake TomahawkW, Lake TomahawkW - 3/28/2013 Very easy to hook up
very satisfied mikelite - rochester ny, rochester ny - 3/28/2013 [...] the product works great
Excellent performance DXnut - Louisville, sville KY - 11/24/2012 The new version of th CM7777 is an awesome pre-amp. It is supurb for those who live near TV stations and those who are in fringe to deep fringe areas and hard core DTV DXers. It use the latest pHEMT device technology which gives abalance of low noise excellent distortion and high-gain. I further improved my pre-amp in the fringe - deep fringe perfomance by replacing the SMD ICs with ones that
Weak cable terminals gcrisler - Rice Lake, Lake Wisc - 12/7/2011 The directions for the setting of the switches are poorly written. The coax connectors are easily twisted off the circuit board if a wrench is used for tightening.
DTV without paying a cable company! bcs - Santa Rosa, a Rosa CA - 8/2/2011 I recofigured my outdoor antenna mast when the digital changeover took place.I installed a dedicated VHF ch 7-14 and a UHF long boom yagi. The CM-7777 VHF and UHF input pre-amp is installed at the mast very close to both antennas. My cable feed is at least 60 ft directly to the TV with an additional distributing amplifier in between. I live in central Sonoma County CA on a hill top 540 ft above se
System Overload Causes Failure to Functi KHH - Eastern Shore o, Eastern Shore o - 7/23/2012 The CM-7777 failed to work completely because as Channel Master technical staff indicated the antennalocation is too close to the TV stations.Most stations are in the 30-49 mile range there are otheres further away and one is at about 20 miles. These conditions caused the amplifier to completely shut down.If that is the case an appropriate warning should be posted to save some users
Enjoy cost-free television with this Metrostar VHF/UHF Amped Omnidirectional HDTV
Antenna from Winegard. The ultimate cord-cutter starter kit, with no rotator needed, it picks up 35+ miles reception of free HD channels in all directions. Capturing VHF and UHF ...
Blonder Tongue DA-33 Wideband Distribution Amplifier - 0.5
This amplifier is designed for a variety of applications, including
signal level meter preamplifier for making FCC required signal leakage measurements, sub-band return amplifier and special purpose amplifier for use aboard ships to provide coverage of the AM, shortwave, ...
Dual Output, -21VDC @ 100mA Dual Output VHF and UHF
Feed Thru Short Circuit Proof Regulator Clamped Output Voltage Protects Loads Panel Mounted Fuse and Auxiliary AC Receptacle. Features. NOTE:Unit can power two preamplifiers, Use with #4761,. #4426, #4706, ...
Solid Signal is an authorized retailer of DISH
Network L.L.C. DISH, DISH Network and DISH Network logos are trademarks, registered trademarks and/or service marks
of DISH Network L.L.C. and/or its affiliate(s). The DISH Network trademarks, registered trademarks and/or service
marks are used under license of DISH Network L.L.C. and/or its affiliate(s).