Solid Signal > Commercial Equipment > Headend Equipment


PDI SAT PDI-60CMS Fixed Frequency Modulators (PDI-60CMS)

Click Images to Enlarge

PDI SAT PDI-60CMS Fixed Frequency Modulators (PDI-60CMS)

Brand: PDI SAT           P\N: PDI-60CMS-SAP          

No Reviews Available  Be the first to write one!


Availability: Discontinued

Looking for something similar? Please contact us at info@solidsignal.com or call us at 877-312-4547 for recommendation.


Call Us For Free Tech Support! Your Purchase is Secure with Solid Signal. View our Frustration Free Return Policy


Description


PDI-60CMS SAW filtered, 60dBmV high performance fixed frequency modulator. This unit is manufactured and thoroughly tested, to comply with and in most cases exceed, all FCC recommended parameters.

Features


  • +60dBmV RF output level (54-860MHz)

  • Frequency range: 54-860MHz plus sub frequencies channels T-7 through T-12

  • FCC offset factory set

  • Under 60dB spurious performance at full output Level

  • Professional grade SAW vestigial sideband filter for true adjacent channel operation

  • BTSC stereo compatible, encoded baseband or 4.5MHz audio Input

Specs


 RF SECTION
Output Frequency 2-134 (54-860MHz) plus sub frequencies T-7 through T-12
Output Level  +60dBmV Typical (Peak Video Carrier)
Output Level Adjustment 20dB Range
Output Impedance 75ohms (Unbalanced)
Spurious Output (@ +60dBmV Output with Aural Carrier 17dB Down) At least 60dB Below Video Carrier
Broadband Noise (@ +60dBmV Output) >80dB Below Video Carrier
Frequency Stability ±5kHz Maximum (±2kHz Typical)
Vestigial Sideband Response -20dB at IF Channel Edge; -60dB a Adjacent Video and
Aural Carrier Frequencies and
 
 
VIDEO SECTION
Input Type Composite Video, Negative Sync
Input Level  0.5 Vp-p Min. for 87.5% Modulation
Frequency Response ±0.75dB (10Hz to 4.2MHz)
Differential Gain 3% Typical at 87.5% Mod. Depth
Differential Phase 3 Deg. Typical at 87.5% Mod.
Hum and Noise 60dB Min. at 87.5% Modulation
Tilt  1.1% Maximum on 60Hz, 50% Square Wave
Group Delay Response Meets FCC Predistortion Requirements for Color Transmission
 
AUDIO
Input Type Unbalanced (Balanced Optional)
Input Impedance 600ohms
Input Level 250mV Min. for 25kHz Peak Deviation
Frequency Response ±1dB (50Hz-15kHz)
FM Hum and Noise 0dB
Subcarrier Frequency 4.5MHz ±500Hz
 
OPERATIONAL
AC Line and Power 85 - 256 Vac, 60Hz, 25 Watts  High efficiency switching mode power supply 
Operational Temperature Operational Temperature 0 to 50 degrees C
Rear Panel Connections RF Output  F Female, Video Input  F Female, Audio Input Screw Terminal (stereo units RCA),  4.5MHz IF Input F Female
  
Front Panel Controls
RF Output Level Adjust
Aural Carrier Level Adjust
Video Modulation Depth Adjust
Audio FM Deviation Adjust (Disabled on stereo units)
 
Front Panel Indicators Power On
 
Rear Panel Control
Baseband Stereo Switch (Pre-emphasis Defeat) (Disabled on stereo units)
4.5 Audio Switch
 


Discuss










Product Reviews for PDI SAT PDI-60CMS Fixed Frequency Modulators (PDI-60CMS)


Product reviews help other customers decide which product to purchase, where the best deals are, and your get a sense of what to expect with the product. Write a Review!



Dish Network Authorized Retailer Solid Signal is an authorized retailer of DISH Network L.L.C. DISH, DISH Network and DISH Network logos are trademarks, registered trademarks and/or service marks of DISH Network L.L.C. and/or its affiliate(s). The DISH Network trademarks, registered trademarks and/or service marks are used under license of DISH Network L.L.C. and/or its affiliate(s).
 ©1999-2016 Solid Signal, Signal Group LLC & Affiliates
  We accept: Checks accepted by Mail