Solid Signal > Tools and Installer Supplies > Signal Meters > Solid Signal S2-T2-C
The Combolook Color HD is a Swedish designed Satellite (DVB-S/S2)- and Terrestrial (DVB-T)- instrument and spectrum analyzer. The unit was designed for the
exact alignment and adjustment of satellite dishes and terrestrial antennas. This instrument is intended to be used by the professionals when accurate and precise
information is needed. With ease of operation through powerful processor technology, basic operation is achieved with only a few controls. The functions are easy to access and only take minutes to learn. Many functions can be controlled by the enclosed Remote
- Spectrum-analyzer 2-900MHz and 950-2150MHz
- QPSK and 8PSK constellation diagram
- DVB-S (Free to Air) and SAT-analog TV-picture
- Aerial power output, 0, 6, 12, 18 and 24V
- LNB voltage 13/18V, 22KHz tone switch
- DiSEqC according to level 1.0, 1.1 and 1.2
- Lots of memory positions for spectrum pictures
- RS232 for PC-connection (up/download)
- Rechargeable Li-Ion battery
- Nice & small, only 8lbs complete with carrying case
- Powered by Emitor
- Presents full range and expanded spectrum
- Very high accuracy, CATV +/-1dB, SAT-TV +/- 1.5dB at 20°C
- Super bright 5” 16:9 TFT-LCD color display
- DVB/S S/2 -receiver 920-2150MHz
- DVB-T measurement, MPEG2 and MPEG4 showing BER, SNR and MER
- Automatic Satellite identification
- Readout of NIT - gives SAT ID and TV/Radio-channel info
- Digital BER and S/N-ratio (DVB-S, S/2 and DVB-T)
A 5 inch 16:9 color TFT-LCD display is provided which shows either normal “Free to air”
satellite TV channels in Analog or DVB-S, CATV Analog and Digital channels, the
frequency spectrum or a Constellation diagram and digital information regarding the signal.
Menus and help displays are shown on the LCD screen (64x128) beside the monitor and a
keypad is used for the function selection. The knob is used for frequency and other
operations. A remote control is provided which allows most of the keypad commands to be
used to control the instrument.
The mode of operation is selected at power on, and to conserve battery life only the
necessary functions are enabled. Switching modes can be done at power on or by menu
Input frequency: 920-2150MHz
Min Input Level: About 35 dBuV (noiselevel).
Max Input Level: About 90 dBuV.
Attenuation: 15 dB manual attenuator on/off.
Accuracy: ±1½ dB TV Accuracy: ±1dB (at +20 C)
Spectrum bandwidth from 250MHz to 1230MHz
Frequency display: Yes, IF default. All standard LNB LO can be used
Display of signal level (Analog): dB-level on Spectrum display
Pitch-tone on loudspeaker for dish/antenna signal strength optimisation
Display of signal level (Digital): SNR (signal/noise-ratio), BER (bit error rate), MER
Constellation diagram (DVB-S, DVB-S2, QPSK, 8PSK normal, 8PSK rotated)
Symbol rate display: 1 to 45 MSymbols/sec
Satellite identification: Yes, NIT display (Network Information Table) according to
the DVB standard. Identifies Satellite Name and position. Name of TV and radio channels
from SDT (Service Description Table)
Analog TV/Audio standard: Multi TV/Audio (PAL, NTSC, SECAM).
Digital DVB-S decoder. MPEG-2 display (MPEG-4 not decoded)
Ku - C-band: Yes, selectable from LNB type defined.
Audio bandwidth : Adjustable between 5.5 MHz and 8.5 MHz
Memory: -100 spectrum pictures can be stored with name.
Stored spectrum can be mixed for easy identification of satellite.
Power out: Yes, 13-18V for LNB can be adjusted.
22 kHz tone: Yes, on/off.
DiSEqC Yes, all 1.0 and 1.1. Also Toneburst on/off.
DiSEqC actuator: Built in positioner for DiSEqC 1.2, SatScan and SatSelect.
DiSEqC Goto X for USALS operation.
TV/CATV (uses TV-IN F-Connector)
Input Frequency: 2–900MHz
Min Input Level: About 35 dBuV (noiselevel).
Max Input Level: Picture = 110 dBuV Spectrum = 120 dBuV
Attenuation: 0dB to 45dB in 1 dB step (Automatic or manual setting)
Accuracy: ±1dB (at +20 C)
Resolution Bandwidth: 1MHz or 300kHz
Video Bandwidth: 100kHz, 1-kHz, 1kHz, or 100Hz
Analog TV/Audio standard: Multi TV/Audio.
Teletext (CEEFAX): Yes
Power for Active Antennas: Yes – 12VDC to 24VDC in 2V steps
DVB-T measurement: Yes, both MPEG2 and MPEG4 showing BER, SNR and MER.
Constellation Diagram: Yes.
Digital Channel Power Function
Memory for Spectrum storage, Channel storage and Favorite storage
Input impedance: 75 Ohm, F Connector
Picture-screen: 5. 16:9 TFT color display.
Menus: On LCD 64x128 next to the monitor.
PC-connection Yes, RS232-output.
Battery: Li-Ion, rechargable 12v, 3.5 amp/hour
Operational: About 1.5 hour on a fully charged battery.
Weight: About 3 kg including battery and carrying-case.
Accessories: Nylon carrying-case.
Power-supply of 220v/13.5v, 1.7amp.
1 Year Warranty on Meter
6 Month Warranty on Batteries
Here are available downloads related to this product:
You May Also Consider
Product Reviews for Solid Signal S2-T2-C Combolook Color HD Spectrum Analyzer (S2-T2-C)
Product reviews help other customers decide which product to purchase, where the best deals are, and your get a sense of
what to expect with the product. Write a Review!