Solid Signal > Marine Equipment > Marine Electrical Accessories > Bep Marine 772-DBC


BEP Pro Installer 400A Dual Bank Control Switch MC10 (772-DBC)

Click Images to Enlarge

BEP Pro Installer 400A Dual Bank Control Switch MC10 (772-DBC)

Brand: Bep Marine           P\N: 772-DBC           UPC: 843687007807

No Reviews Available  Be the first to write one!


Availability: Usually Ships Same Day
Condition: New


Your Price: $5499


List Price: $81.99




Qty:


Call Us For Free Tech Support! Your Purchase is Secure with Solid Signal. View our Frustration Free Return Policy


Description


Pro Installer 400A Dual Bank Control Switch - MC10, Another addition to our multi award winning Pro Installer EZ Mount range, the innovative Dual Bank Control switch is like 3 switches in one, House, Start, and Emergency Parallel. Offering easy intuitive control for the boater, the Dual Bank Control switch features a unique isolated-On position which allows use of house loads and VHF radio if the engine needs to be electrically isolated, or allows the engine to be isolated during servicing while still providing power to house loads (for lighting, stereo, fridge etc). For boats or vehicles with single Engine and House battery bank, Dual Bank Control allows the use of optimized battery banks for their respective loads; an appropriately sized deep cycle bank for House loads, and thin plate starting batteries for the Engine. Further, sensitive electronics are isolated from starter motor induced voltage spikes because House and Engine loads are separated during normal operation, unlike Selector battery switches. As easy as 1, 2, 3, these revolutionary EZ Mount battery switches allow you to wire from the front for the easiest surface mounting. With their shared interconnection height, EZ-Mount battery switches "cluster" directly with the Pro Installer Busbar Range, resulting in the fastest, most compact installations. Optimized cable access makes installation a breeze. 400A Continuous / 600A 5 minutes Intermittent / 1500A 10 seconds Cranking (cable size to achieve ratings 120mm}, 4/0, smaller cable size will reduce the Amp rating), Specifications: Mounting: Surface, Rear or Front, Voltage: 48v DC (for 12-48v systems, both banks must be same voltage), Rating: 400 Cont / 600 Inter / 1500 Crank, Dims: 3.85" x 3.85" x 3.62", Operation: 1, 1/2, Parallel, Off, Stud: 4x 10 mm (3.8").

Key Features:

  • Tested to UL1107 ignition protection, CE, Tinned copper 10mm (3/8 inch) studs
  • Stainless steel washers and nuts, Fiber reinforced plastics
  • Same interconnection height as Pro Installer, Removable knob allows isolation during servicing, Waterproof to IP67
  • 3 removable side plates for protection, Industry standard 3.85 x 3.85 inch footprint, For surface mounting only
  • Each Pro Installer battery switch is fully tested for pressure sealing, rotation force and electrically load tested




Discuss





RELATED SEARCHES







Product Reviews for BEP Pro Installer 400A Dual Bank Control Switch MC10 (772-DBC)


Product reviews help other customers decide which product to purchase, where the best deals are, and your get a sense of what to expect with the product. Write a Review!



  RELATED PRODUCTS
Related Products
m-Series (Mini) Battery Switch, Single Circuit ON/OFF, Switches a single ...
Push/Pull Switch Two-Position, off/on. For operating one set of lights ...
Push/Pull Switch Three-Position, off/on/on. For operating running lights and anchor ...


Dish Network Authorized Retailer Solid Signal is an authorized retailer of DISH Network L.L.C. DISH, DISH Network and DISH Network logos are trademarks, registered trademarks and/or service marks of DISH Network L.L.C. and/or its affiliate(s). The DISH Network trademarks, registered trademarks and/or service marks are used under license of DISH Network L.L.C. and/or its affiliate(s).
 ©1999-2017 Solid Signal, Signal Group LLC & Affiliates
  We accept: Checks accepted by Mail